Air Flow Studies
Categories: Laboratory Research Equipment ManufacturerAir Flow Studies Air Flow Studies helps to determine the important characteristics of industrial air distribution systems. It demonstrates the principle of fluid Mechanics to analyze flow in...
Product
Description
Air Flow Studies
Air Flow Studies helps to determine the important characteristics of industrial air distribution systems. It demonstrates the principle of fluid Mechanics to analyze flow in ducts and jets.- The unit is self-contained and only requires connection to a single-phase electrical supply.
- Turbulence in the 80mm diameter test pipe is minimized by locating the pipe at the inlet of the centrifugal fan.
- A profiled bell mouth inlet prevents air-separation from the wall of the pipe at the entrance and straightening vanes suppress the formation of vortices.
- Tappings along the test pipe allow the pressure gradient to be measured with air velocity variable up to a maximum of 35m/s.
- A Pitot tube can be traversed across the pipe at five locations to allow boundary layer growth/development of velocity profile to be examined.
- Air flowrate is determined from differential pressure measurements across an orifice plate or two different inlet nozzles.
- Different bends and elboes can be fitted to allow frictional losses in fittings to be compared.
- Air jet dispersion experiments are carried out on the discharge side of the fan.
- A Pitot tube can be traversed laterally (across) and longitudinally (along) the jet to measure the changes in velocity as the jet disperses.
- All pressure measurements are performed using a bank of fourteen manometer tubes that can be inclined to increase sensitivity.
- An instruction manual is supplied that describes how to perform the air flow experiments and interpret the results, as well as how to install, commission and maintain the equipment.
Technical Details :
| Item | Value |
| Centrifugal fan capacity: | 218 l/s at STP |
| Pipe velocity range: | 0-35m/s |
| Inlet pipe: | dia.80mm length 2.75m |
| Interchangeable nozzles: | dia.50mm and 80mm |
| Internal pipe orifice: | dia.50mm |
| Jet discharge pipe orifice: | dia.30mm |
| Jet traverse range (downstream lengthxwidth): | 600mm x 140mm |
| Manometer range: | 0 - 283mm H2O |
quick overview :
Air Flow Studies
Air Flow Studies helps to determine the important characteristics of industrial air distribution systems. It demonstrates the principle of fluid Mechanics to analyze flow in ducts and jets.- The unit is self-contained and only requires connection to a single-phase electrical supply.
- Turbulence in the 80mm diameter test pipe is minimized by locating the pipe at the inlet of the centrifugal fan.
- A profiled bell mouth inlet prevents air-separation from the wall of the pipe at the entrance and straightening vanes suppress the formation of vortices.
- Tappings along the test pipe allow the pressure gradient to be measured with air velocity variable up to a maximum of 35m/s.
- A Pitot tube can be traversed across the pipe at five locations to allow boundary layer growth/development of velocity profile to be examined.
- Air flowrate is determined from differential pressure measurements across an orifice plate or two different inlet nozzles.
- Different bends and elboes can be fitted to allow frictional losses in fittings to be compared.
- Air jet dispersion experiments are carried out on the discharge side of the fan.
- A Pitot tube can be traversed laterally (across) and longitudinally (along) the jet to measure the changes in velocity as the jet disperses.
- All pressure measurements are performed using a bank of fourteen manometer tubes that can be inclined to increase sensitivity.
- An instruction manual is supplied that describes how to perform the air flow experiments and interpret the results, as well as how to install, commission and maintain the equipment.
Technical Details :
| Item | Value |
| Centrifugal fan capacity: | 218 l/s at STP |
| Pipe velocity range: | 0-35m/s |
| Inlet pipe: | dia.80mm length 2.75m |
| Interchangeable nozzles: | dia.50mm and 80mm |
| Internal pipe orifice: | dia.50mm |
| Jet discharge pipe orifice: | dia.30mm |
| Jet traverse range (downstream lengthxwidth): | 600mm x 140mm |
| Manometer range: | 0 - 283mm H2O |
Product
Reviews
add Review
reviews
No Review Yet.
Related
Products
The bench is made of thick ply board, and reinforced with te...
Laminar Air Flow Horizontal With Stand
Laminar Air Flow Horizontal With Stand FEATURES :- • W...
Laminar Air Flow Vertical The bench is made of thick ply boa...
Laminar Air Flow Table Top Model
Laminar Air Flow Table Top Model The bench is made of thick...
Inclined Laminar Air Flow For Filling &...
Inclined Laminar Air Flow For Filling & Ceiling Machine...
Laminar Air Flow Hanging Mode For some applications it may...
Heating Mantles Made of glass yarn with On/Off switch. avai...
Clean Air Tent These are overhead clean air tent modules mou...
Copyrights © 2019 All Rights Reserved by Atico
Product
Reviews
add Review
reviews
No Review Yet.